Mr. YUSRASAAD

Department of Dental Technology Faculty of Medical Technology

Full name

Mr. YUSRA MUFTAH GUMMA SAAD

َQualifications

Master degree

Academic Rank

Assistant Lecturer

Biography

Removable and Maxillofacial Prosthodontist. Assistant lecturer at Removable prosthodontic department, Faculty of Dentistry, University of Benghazi since 10/2019-8/2021. Assistant lecturer at Dental technology department, Faculty of medical technology, University of Triopoli since 9/2021- present time

Download CV

Contact Information

روابط التواصل

الاستشهادات

الكل منذ 2017
الإقتباسات
h-index
i10-index

Publications

LABORATORY EVALUATION OF PRE-POLYMERIZED DENTURE BASE MATERIAL USED FOR CAD/CAM COMPLETE DENTURE MANUFACTURING

INTRODUCTION: CAD/CAM denture base materials are milled from pre-polymerized pucks of resin that are highly condensed. So, they provide no polymerization shrinkage eliminating its subsequent disadvantages. This technology offered improved fit, strength properties and more bio-hygienic denture bases compared with conventional processing of the denture base material. OBJECTIVES: The aim of the study was to evaluate the physico-mechanical properties of CAD/CAM denture base material and the effect of thermo-cycling on it compared with the conventional one. MATERIALS AND METHODS: The study was conducted on two parallel groups, divided according to the denture material used. Group (1) conventional PMMA (control group), group (II) CAD/CAM PMMA (study group) of 40 specimens each (16 for impact strength, 16 for flexural strength, 8 for surface roughness and grinded powder form both materials for residual monomer test). Each group was divided into 2 sub-groups: (A) No thermo-cycling and (B) Thermo-cycling, then subjected to 4 different tests, impact strength, flexural strength, surface roughness and residual monomer tests. Data were collected, tabulated and statistically analyzed. Significance level was set at 5%. Bar charts were used for graphical presentations. RESULTS: Our study revealed a highly statistically significant decrease in residual monomer of CAD/CAM PMMA material in both conditions before and after thermo-cycling when compared to conventional PMMA material, which therefore leads to enhanced impact strength and significantly reduced surface roughness after heat treatment. On the other hand, also a highly significant reduction of its flexural strength after thermocycling has been observed. CONCLUSIONS: CAD/CAM dentures with lower amount of methacrylate monomer exhibit more favourable physico-mechanical properties and they have a long-term biocompatibility even with thermal changes making them a more satisfactory as a denture base material for edentulous patients.
Yusra Muftah Saad Elfaidy, Ahmed M. Abdelhamid, Sonia M. Elshabrawy(12-2018)
Publisher's website


Attitude of Dental Clinicians Towards Flexible Dentures: A Questionnaire Survey in Libya

Background: Management of partially edentulous patients with hard and soft tissue undercuts is complicated, and the use of flexible dentures for these cases offers dual advantages of aesthetics and flexibility. However, research shows a varying preference for flexible dentures among general dental practitioners, prosthodontists, and other dental specialties. Objectives: The aim of this study was to survey the attitude and awareness of a sample of Libyan dental clinicians towards advantages, disadvantages, indications, and contraindications of flexible dentures. Material and methods: A descriptive cross-sectional study was conducted among 250 dentists currently practicing in different cities of Libya. Only 218 dentists responded. Using Google form software, a self-administrable e-questionnaire consisting of thirty-one multiple choice questions with "yes," "no" or "not sure" answers encompassing major aspects of flexible dentures was conducted through an online survey. Results: Out of 250 Libyan dentists to whom the questionnaire was sent, only 218 dentists responded and our results revealed that the respondents were females more than males with a ratio (2:1) and more than half of them were of age group (35-60 years) work in governmental dental practice with more than ten years of experience and 34.9% of them prefer and often offer flexible dentures to their patients. The majority of respondents with a long-term success of the flexible denture were prosthodontists who had more than ten years of experience with a correct response rate of more than 50% of questions that reflected their attitude and knowledge. Conclusions: Despite the fact that flexible dentures are not taught in Libyan universities of dentistry, about more than one-third of respondents prefer and recommend this treatment to their patients, and the long-term success of these prostheses was dependent on clinicians' education and their clinical experience.
Yusra Muftah Saad Elfaidy, Warida Abdalla Elnaihoum, Aseidah Abdullah Elgotrany(4-2022)
Publisher's website